Shop

Tootekirjeldus

Filtreerimisklassid
F7 – ePM1 55% | M5 – ePM10 60% | G4 - ISO 16890 coarse
Suur filtreerimisala
Suurem filtreerimisala tagab filtri pikema eluea
Kontrollitud mõõdud
Filtrid on tootja poolt määratud täpsete mõõtudega
Tootmiskogemus
Meil on üle 20 aasta kogemust ja tootearendust
Filtriraami kirjeldus
Filtriraam koosneb fiibermaterjalist 200g/m2
Madal rõhukadu
Tagab seadmes väiksema müra ning elektritarbimise
Tootmine
Meie filtrid on toodetud Baltikumis ja Skandinaavias
ISO 16890
Meie kõik filtrid vastavad ISO 16890 standarditele

Vallox Digit 2 SE filters

Vallox Digit 2 SE filters are designed to filter the supply and extract air of the Vallox Digit 2 SE ventilation unit. The set (Vallox filter set no. 18) includes a F7 panel filter and two G4 filter media sheets. The F7 filter measures 432 × 189 × 28 mm and the G4 filter media sheets measure 433 × 175 mm.

The right filters help reduce the amount of dust and other airborne particles entering the ventilation system. Before ordering, check your unit’s exact model designation and compare the filter dimensions.

Filter set specifications

  • Compatible unit: Vallox Digit 2 SE (R and L models)
  • Set contents: 3 filters
  • Supply air filter: F7 panel filter
  • Supply air filter dimensions: 432 × 189 × 28 mm
  • G4 filter media sheet: 2 pcs
  • G4 filter media sheet dimensions: 433 × 175 mm

More information and FAQ

Open a question to read more.

How do I check that the Vallox Digit 2 SE filters fit?

Before ordering, make sure your ventilation unit model is Vallox Digit 2 SE. The F7 filter in this set measures 432 × 189 × 28 mm and the G4 filter media sheets measure 433 × 175 mm. We recommend comparing them with your current filters, as Vallox Digit SE and Digit 2 SE filters are different sizes.

How do I install the Vallox Digit 2 SE filters?

The set includes a F7 panel filter and two G4 filter media sheets. The F7 filter cleans the fresh outdoor air, and the G4 sheets capture coarser dust.

Unplug the unit before replacing the filters. Check the correct installation position of the filters and the airflow direction marked on the filter, and follow the unit’s maintenance instructions. Also see the Vallox Digit 2 SE filter replacement guide (PDF).

In the Vallox Digit 2 SE unit, one G4 sheet is placed flat and without wrinkles on the side of the F7 filter where the air comes in and slid into place together with the filter. The second G4 sheet is for the extract air and goes on its own support mesh. The arrow on the F7 filter must point in the same direction as on the old filter: away from the G4 sheet, into the unit. So before removing the old filter, check where its arrow points or take a photo with your phone. In the left-hand (L) model everything is mirrored. After replacing the filters, reset the service reminder on the control panel.

How often should ventilation filters be replaced?

Ventilation filters should generally be replaced every 6 months. In dustier environments, near busy roads or where air pollution is higher, more frequent replacement may be needed.

Regular maintenance helps keep indoor air quality good and your ventilation unit running efficiently. Also follow the manufacturer’s maintenance recommendations.

Why is it important to use the right filters for your ventilation unit?

Filters of the correct size and filter class help keep your ventilation unit working properly and filter the air effectively. Unsuitable or heavily soiled filters can increase air resistance and reduce the performance of the ventilation system.

See other Vallox filters

If your ventilation unit is a different model, browse the Filt.ee range of Vallox filters. On the category page you’ll also find filter sets for other Vallox ventilation units.